10W 120..350mA 9-42V DALI 2.0 Dimmable Constant Current LED Driver

AURA+ ALCC10 LED DRIVERS SERIES

DALI/TOUCH DIM (PUSH DIM) DIMMABLE CONSTANT CURRENT LED DRIVER - ALCC010-00350-042-DALI

FEATURES

• Single channel output, output current level selectable by DIP S.W.

• Support DALI 2 dimming function, Touch DIM (Push DIM) function

• Input voltage of 120-277VAC

• Dimming range: 0.1-100% Dimming is smooth, no flicker

• Half Potted Electronics

• Protections: Short circuit, Over load, Over voltage

APPLICATION

• Suitable for indoor LED lighting application

IP Class

IP20

Constant Current

120mA

150mA

210mA

180mA

260mA

290mA

320mA

350mA

TECHNICAL DATA

OUTPUT

DIP Switch Technical Values

DIP Switch Technical Values

• 120mA 9-42V 5.04W
  
• 150mA 9-42V 6.3W
  
• 180mA 9-42V 7.56W
  
• 210mA 9-42V 8.82W
  
• 260mA 9-38V 9.88W
  
• 290mA 9-34V 9.86W
  
• 320mA 9-31V 9.92W
  
• 350mA 9-28V 9.8W

Channel: 1
No load output voltage: 58V Max
Frequency: 1KHz Min PWM
Current Tolerance: ±5%
LF current ripple(<120Hz): <3%

INPUT

Voltage: 120VAC-277VAC
Frequency: 50/60Hz
Efficiency: 80%@120VAC, Full load
PF: 0.98@120VAC, Full load
THD(full load): <10%@120VAC, Full load
Current: 0.12A max @120VAC
Inrush Current: Cold start, 30A@120VAC

PROTECTIONS

Over Voltage: Hiccup, recovers after fault condition is removed
Short Circuit: Close output, recovers automatically after fault removed
Over load: Hiccup, recovers after fault condition is removed

DIMMING

Dimming type: DALI/Touch DIM (Push DIM)
Dimming range: 0.1%-100% Dimming to off

ENVIRONMENT

IP rating: IP20
Working temp.: -20 ~+50°C
Tc.: +90°C
Relative humidity: 20~90% RH

DIMENSIONS

Lenght: 75mm
Width: 35mm
Height: 26.5mm
Lenght of the wires: 150mm
Weight: 96g
Material: PC

SAFETY

Surge: L-N:1KV
Withstand Voltage: I/P-O/P: 3000VAC/1min/5mA; I/P-Gnd: 1500VAC/1min/ 5mA; O/P-Gnd: 500VAC/1min/5m
Safety standards: UL8750/UL1310/CSA25013,CSA class P
EMI Eission: EN55015,EN61000-3-2 Class C,IEC61000-3-3
EMC Immunity: FCC class B(120V)/class A(277V)

LIFETIME

Lifetime: 50,000h@tc:85
Switch cycle: >25,000 times

PUSH DIM FUNCTIONS

1. Press the Touch DIM (Push DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Touch DIM (Push DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Touch DIM (Push DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Touch DIM (Push DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing Push DIM switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.

CAUTIONS

1. This product should be installed by qualified personnel.
2. This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3. Good heat dissipation conditions extend product life.Please install the product in a well-ventilated environment.
4. Please make sure LED power supply output voltage, current is used to meet the product requirements.
5. Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6. Due to safety concerns, PVC or rubber cord of 0.75-2.5mm2 is recommended for input and output terminal(s) (excluding signal terminals). Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
7. In case of malfunction, do not repair it yourself.

If the product or model you have been looking for is out of stock, subscribe to availability notification.