70W 1400mA 33-47V DIM 1-10V LED DRIVER ROAL STRATO

ROAL / EFORE LED DRIVER CC 70W, Single Output - RSLD070-14

Features

STRATO switch mode driver technology is designed to generate one constant current output from a wide
range AC input. The size and performance of these products make them the ideal choice for LED lighting
applications.

-Wide Range Input: 120, 240, or 277 VAC
-Constant Current Output for Powering LEDs Directly
-High Efficiency ~90%
-Compact Design
-Adjustable Output Current Settings
-Dimmable with (0-10VDC) Input
-Temperature Protection for LEDs
-Convection Cooled
-Long Life
-Wide Temperature Range
-ROHS Compliant

Protection: IP64 Rated

Application and Benefits

STRATO is designed for directly powering LEDs in commercial & industrial lighting applications.

The product’s extremely small form factor and high efficiency makes it suitable for integration into most
light fixtures and standard electrical junction boxes.

A host of integrated control features:
 -Simplify Light Fixture Design
 -Ease Safety Approval Cycles
 -Lower Fixture Complexity and Cost

IP Class

IP64

Constant Current

1400mA

Input and Output Specifications

-Input Voltage: 120 / 240 / 277 VAC nominal
-47-63 Hz Frequency Range
-Efficiency: 90% typical *
-Isolation: Meets UL60950-1 Reinforced/double insulation NEC (Class 2) EN60598-1 Class II
-Input Power Factor: >0.90 *
-Input Harmonics: Meets EN61000-3-2, -3 *
       * @ Vin Nominal and >80% load

-Output Voltage: 33..47V / Vout No Load Max: 60vdc
-Output Current: 1400mA
-Output Current Regulation: +/- 3% of max rating
- Ripple Current: <45% (P-P) of maximum Output Current
-Output Over-voltage, Over-Current and Short-Circuit Protection (hiccup), and over-temperature protection with auto recovery

Performance Requirements: Meets the requirements of IEC 62384; control gear for LED modules

Controls

Output Controls: Two dedicated inputs provide control and safety features.

Dim: A dimming input can be used to adjust the output setting via a standard commercial wall dimmer,
an external control voltage source (1 to 10VDC), or a variable resistor when using the recommended
number of LEDs. The input permits 100% to 80% trimming and 100% to 10% dimming. This permits
active control of the driver and may be used for trimming and dimming purposes. See Roal Strato
Application Note 1 for details on functionality and compatibility with standard industry practices.

Ts: The Temperature input may be connected to a 100k NTC thermistor. The thermistor should be
located on the LED assembly to monitor its temperature. If the temperature exceeds a predetermined set
point, the output current of the module is automatically reduced to regulate the temperature of the LED
at a safe level. See Roal Strato Application Note 1 for details.

Mechanical Details

I/O Connections: Flying leads, 18AWG on power leads, 20AWG on control leads, 152mm long, 105C Rated, Stranded, Stripped by approximately 9.5mm and tinned

Mounting Details: Universal Mounting Clips, and 6 mounting locations per package allow installer to choose the most suitable position for the mounting feet.

Enviromental / EMC

Operating Temperature: -30 to +90C case temperature without derating
Operating Relative Humidity: 5% to 95%, non condensing
Storage Temperature: -40°C to +85°C
Surface Temperature: Exposed surfaces <90°C under all operating conditions
Cooling: Convection cooled

EMI and EMC:
Conducted and Radiated EMI: EN55015 Class B, FCC 47CFR Part 15 Class B
Susceptibility: EN61000-4-2, -3, -4, -5, -6, and -11
ANSI c62.41-1991 Category A1, 2.5kV Ringwave

Safety Agency Approvals

UL60950-1 Recognized, UL8750 recognized, approved for damp locations
EN61347-2-13 electronic control gear for LED Modules
ENEC Mark and CE Mark for EU.
Notes Regarding European (ENEC) approvals:
     1. All models with Vout > 25VDC are considered “Isolated Control Gear” per EN61347-2-13